What have you done to your car today?
- Thread starter Buckz
- Start date
- Featured
Arnie_one said:
Where did you source these?
Collected my refurbished interior parts. New sponges, leather repainted, gyeon leather shield added for protection. (640 euros)
The guy that refurbished leather parts also repainted the new center console button from aliexpress, looks like new.
Also bought all new beige cover strips from main dealer, plastics that go from footrest to the back (3 parts each side). (150 euros)
Will mount tomorrow
The guy that refurbished leather parts also repainted the new center console button from aliexpress, looks like new.
Also bought all new beige cover strips from main dealer, plastics that go from footrest to the back (3 parts each side). (150 euros)
Will mount tomorrow
Z4supercharged
Member
iamnotme said:
I think you have long way, i am from other country
this is what I did a couple of days ago....forgot to put the backing plate on before fitting my new wheel bearing 
Untitled by Damien Bower, on Flickr
Untitled by Damien Bower, on Flickr
futureZ4buyer said:Collected my refurbished interior parts. New sponges, leather repainted, gyeon leather shield added for protection. (640 euros)
The guy that refurbished leather parts also repainted the new center console button from aliexpress, looks like new.
Also bought all new beige cover strips from main dealer, plastics that go from footrest to the back (3 parts each side). (150 euros)
Will mount tomorrow
IMG_0082.jpg
IMG_0078.jpg
IMG_0077.jpg
The seats look amazing!!!
Finally got the new water pump installed. But because it’s now working properly, it’s putting too much stress on the connection between the radiator and reservoir connection. New total aluminum radiator coming in Tuesday. Also got new fender clips in and put those on. That was a total beast! That was about as bad as putting on the water pump. Today I’m just gonna chill and go wash her and continue to fix a few plastic welding issues on the interior.
Attachments
TrackMyZ said:
Also i, i bought MAHLE BEHR OEM, everything is now prepared for sesson
New break pads
New Thermostat
New screw for expansion tank and cooler
New new shock absorber cups
New adjustable arms
Oil and filtrers
Geometry
New DISA
What is misssing is only sun
Crankshaft ventilation and Oil separator
Clean everything
Remote roof
oil cover
Rubberboot air intake and clean regulating valve
New oil in automatic transmission
i have clean and impregnated roof
New expansion tank and watter hoses
New AUT termostat
New compressor fridge max -25
for the trips
New breaks, calipers, spark plugs etc.....many things
Brembo, rotors are good (10kkm), but breaks pads sucks - after few km they squeal, i have changed to my favorite Textar F/R - TEXTAR 2328702, TEXTAR 2193402, brakes pads are well without bad noises, only, they are very dirty and they are softer.
This type of textar i have on all cars, E70/ E63/ E85/ E53.
This type of textar i have on all cars, E70/ E63/ E85/ E53.
3002 tii
Active member
Nick W said:Condensation in in the starboard headlight. Left this running for 3 hours with the back cover off and a blast from Deb's hairdryer every 15 min or so to shove some dry air around inside and job Done. Thought the video would be a bit boring.
Hopefully you replaced both headlight cover with a new one. Those rubber gaskets dry up over time.
Do you find drilled brembos louder than a standard rotor? I had drilled Zimmermanns on my e39 and they were louder than the previous standard discs, at least when they were new. Later they got quieter or I just got used to the noise. When I replaced them with standard discs back again I didn't really noticed the new rotors to be quieter. But the inner holes on the Zimmermanns got filled, maybe that silenced them.Arnie_one said:
I am however thinking of trying the drilled brembos on my Z4 in the future.
Has anyone had drilled brembos to work with Ate Ceramic pads?