Diagnostic Services - Members Register (INPA, Carsoft etc.)
- Thread starter EdButler
- Start date
just loaded SSS v32 on to laptop running window 7 (32 bit)
Have made the follow mods:
Auto lock after moving off
Auto lock if not opened after 2 mins.
Indicators flash on lock and unlock
Altered memory seats to be set on unlocking car
Found in retro fit section that you can deactivate driver or passenger seat belt warning, tried it but need to connect car to charger as you need over 13 volts
will give it ago another day.
Have made the follow mods:
Auto lock after moving off
Auto lock if not opened after 2 mins.
Indicators flash on lock and unlock
Altered memory seats to be set on unlocking car
Found in retro fit section that you can deactivate driver or passenger seat belt warning, tried it but need to connect car to charger as you need over 13 volts
will give it ago another day.bs0u0118 said:
Are you using a virtual machine to an INPA cable, or a proper GT1 head?
I've got INPA which I really like but I'd like to try out the SSS but you need to run VMWare to make the INPA head be seen as a GT1, from what I can gather anyway.
Cheers
Dave
kishanvaja
New member
Hi,
This forum is an excellent place to come may I point out before I start... Bought my Z4 two months ago and I've been here often finding out bits and pieces so hats off to everyone.
I'm looking to have a few things programmed on my 2004 Z4 E85 and I'm in the Milton Keynes area.
- Indicator flash on lock/unlock (+audible sound if possible)
- Increase the sensitivity of auto wipers and headlights
- Anything else which may be of use (maybe being a bit greedy now).
I've seen the cables on ebay but in all fairness not sure what all this SSS, Inpa etc. mean so any help there would be much appreciated.
Thanks
Kish
This forum is an excellent place to come may I point out before I start... Bought my Z4 two months ago and I've been here often finding out bits and pieces so hats off to everyone.
I'm looking to have a few things programmed on my 2004 Z4 E85 and I'm in the Milton Keynes area.
- Indicator flash on lock/unlock (+audible sound if possible)
- Increase the sensitivity of auto wipers and headlights
- Anything else which may be of use (maybe being a bit greedy now).
I've seen the cables on ebay but in all fairness not sure what all this SSS, Inpa etc. mean so any help there would be much appreciated.
Thanks
Kish
I did the rear light conversion in my car, and everything is working fine, but how can I eliminate the error light on my dash???
I have NCSexpert program and I know how to use it, so far I have change this codes to (nicht_ active) and the error light still on the dash, what am I doing wrong, please help!!!!
WARMUEBERWACHUNG_RL_LI
WARMUEBERWACHUNG_RL_RE
KALTUEBERWACHUNG_RL_RE
KALTUEBERWACHUNG_RL_LI
CC_RUECKLICHT_LINKS
CC_RUECKLICHT_RECHTS
I have NCSexpert program and I know how to use it, so far I have change this codes to (nicht_ active) and the error light still on the dash, what am I doing wrong, please help!!!!
WARMUEBERWACHUNG_RL_LI
WARMUEBERWACHUNG_RL_RE
KALTUEBERWACHUNG_RL_RE
KALTUEBERWACHUNG_RL_LI
CC_RUECKLICHT_LINKS
CC_RUECKLICHT_RECHTS
fercho said:
did you do the following:
1. the tail lights and break light is on
well, to prevent the "t" effect, you just have to code your light control module - in german the code is:
BREMSLICHT_ALS_STANDLICHT
nicht_aktiv
this means the breaklight should not longer work as your side markers and then they are off. everything works as intended (break, tail light..)
2. flickering of taillight / 6V issue
well, you took the power of the light of your plate sign - you can also program your light control module as follows:
PWM_ANSTEUERUNG_SL_RE_HI
wert_01
PWM_ANSTEUERUNG_SL_LI_HI
wert_01
Yes
You need to apply codes otherwise you will haves "T" effect in lights and lights will flicker due to 6v supply. You also need to apply other codes to stop having bulb out light on dash as car cannot isn't programmed with LED lights.
Sent from my iPad using Tapatalk HD
You need to apply codes otherwise you will haves "T" effect in lights and lights will flicker due to 6v supply. You also need to apply other codes to stop having bulb out light on dash as car cannot isn't programmed with LED lights.
Sent from my iPad using Tapatalk HD
Similar threads
