>
Passenger one touch window not working up
- Thread starter Nathanio
- Start date
I may be wrong but I am sure it is a codable option, certainly on the post facelift. It may just need enabling with NCS/Carly.enuff_zed said:
Could be that too and pre 4/2004 might still be out of luck, says some posts. The alternative reset was with doors closed, open window fully and immediately click open four times within 10 seconds. Then do the conventional close window and holding wait for click, open window and holding wait for click, close window anf holding wait for click -sequence.enuff_zed said:
Thanks for confirming my brain still works :lol:patriot66 said:
Notes on initializing power window unit (from 04/2004)
Warning!
Danger of injury!
There is no anti-trapping protection during initialization.
Note:
Cars built prior and up to 04/2004 have no anti-trapping protection and on the passenger side no toll closing function.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
Initialization with engine running
Convertible top, doors and windows closed
Initialization comprises:
Erasure of initialization
Reinitialization
An initialization must be performed:
In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
After the power window drive has been replaced
After work is carried out on the power window mechanism
After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
After the door window glass has been removed and installed or replaced
After adjustment work on the door window glass
After adjustment work on the convertible top
After replacement of seals
Erasure of initialization:
Open door window glass fully
Operate power window switch in ”Open” position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
This completes initialization.
Note:
Carry out function check (one-touch control function, anti-trapping protection and, if necessary, comfort function).
Warning!
Danger of injury!
There is no anti-trapping protection during initialization.
Note:
Cars built prior and up to 04/2004 have no anti-trapping protection and on the passenger side no toll closing function.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
Initialization with engine running
Convertible top, doors and windows closed
Initialization comprises:
Erasure of initialization
Reinitialization
An initialization must be performed:
In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
After the power window drive has been replaced
After work is carried out on the power window mechanism
After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
After the door window glass has been removed and installed or replaced
After adjustment work on the door window glass
After adjustment work on the convertible top
After replacement of seals
Erasure of initialization:
Open door window glass fully
Operate power window switch in ”Open” position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
This completes initialization.
Note:
Carry out function check (one-touch control function, anti-trapping protection and, if necessary, comfort function).
Just because BMW say so, doesn't mean they're always right :lol:enuff_zed said:
Well worth trying for the early models.BumpyZ4 said:
Isn't it odd that BMW don't say that. Thankfully easy to prove them wrong!1000rr said:
It's because it's a safety feature - my MG ZT had the software capability to do one touch up on all windows, even the pins on the ECU for the sensors, but only the drivers side window had an anti-trap sensor, so thats the only one that worked.Scooba_Steve said:
Having had my hand trapped in a window, it's not fun. But not super painful.
OK I think I get it now. Anti-trap isn't a feature pre-04, so one touch was disabled. Except contrary to the guidance, it is possible (though doubt via DIS/ISTA as an option).Jakg said:
BMW list build dates prior to 04/2004 as lacking.markplant said: