Monkey exhaust tips

[SonnyA85]

Sounds good, pop a picture up, worth a thousand words

Will do tomorrow. just fitted them and it's pitch black outside. had to file one of the sides on one of them as it was a tad too big. one was quite loose the other too tight.

I nearly broke the allen key tightening them.

I ended up with both roughly the same length. Tried to get them bang on but might be a mm or two out due to being pitch black outside.

 

[Machine monkey]

Sounds good, pop a picture up, worth a thousand words

Will do tomorrow. just fitted them and it's pitch black outside. had to file one of the sides on one of them as it was a tad too big. one was quite loose the other too tight.

I nearly broke the allen key tightening them.

I ended up with both roughly the same length. Tried to get them bang on but might be a mm or two out due to being pitch black outside.[/quot

Sorry i have been away for the weekend.

If your still having problems just ask. As for witch one where thats up to you and how you want them to look. I would suggests for a more standard look put the shorter one on the out side. If you want them to stick out more than standard you could swap them? As for the fitting i check them all on a gauge to make sure they will all fit. But some do come up tighter than others.

 

[Ducklakeview]

Hoping mine arrive this week 8)

Mike

 

[Machine monkey]

Ok guys I have 1m of material left so 5 sets in total I have orders that will keep me busy until in the evenings this week and then the weekend. after that i will do these last 5 sets and then thats it for a while. I have lots of stuff to do to the Toyota build my car and DIY around the house. Plus I have made a lot of them and just want a rest from them for a while.

PM me if you want them.

 

[Machine monkey]

4 sets left.

 

[SonnyA85]

Can everyone please check and give feedback please.

http://imgur.com/a/336jZ

I think they are too close, need to separate them slightly. Don't know if both are angled towards the middle or it's just 1 of them that needs adjusting.

 

[Machine monkey]

Can everyone please check and give feedback please.

http://imgur.com/a/336jZ

I think they are too close, need to separate them slightly. Don't know if both are angled towards the middle or it's just 1 of them that needs adjusting.

I would say that the gap needs opening up. There is a bigger gap at the back. Simply undo one pull it over to the correct position. Then hold it in place when you tighten it up. Also they are sticking out the same amount. They tend to look better (in my opinion) if the left as you look at the back of the car. Is shorter than you have it so that it follows the curve of the bumper.

 

[JimsZ]

Finally got round to fitting mine this afternoon, they look great

DSC05210 by Jimhas7, on Flickr


DSC05212 by Jimhas7, on Flickr

Look sooooo much better than the OEM tat that was on there

I know it's a different model, e89 but I would do them more like mine as described by MM.

 

[Tcochrane92]

I'll take a set for a pre-facelift 3.0

 

[Ducklakeview]

4 sets left.

Is one of those mine Mat?

Mike

 

[Machine monkey]

4 sets left.

Is one of those mine Mat?

Mike

I am sure yours are in the post on there way.

 

[Ducklakeview]

4 sets left.

Is one of those mine Mat?

Mike

I am sure yours are in the post on there way.

Cheers Mat! Look forward to getting them.

Mike

 

[Axelf]

Hi Mat I have just bought a Z3 2.8 .. Do you have any exhaust tips to fit this ? Thanks

 

[Ctrl-Z]

Received my tips on Thursday and install yesterday. They look awesome. Will post a pic when I get a chance..

Great work Mat. Thanks

 

[Machine monkey]

Hi Mat I have just bought a Z3 2.8 .. Do you have any exhaust tips to fit this ? Thanks

I am sure I can make them your in oxfordshire right? If so we can meet up and I can take a look and let you know.

 

[Machine monkey]

Received my tips on Thursday and install yesterday. They look awesome. Will post a pic when I get a chance..

Great work Mat. Thanks

No problem at all they took a while getting all that way!! Glad you like them buddy

4/3 sets left plus a damaged set to fit a 3.0l you won't tell they are damaged once fitted these are £25

 

[Axelf]

Hi Mat I have just bought a Z3 2.8 .. Do you have any exhaust tips to fit this ? Thanks

I am sure I can make them your in oxfordshire right? If so we can meet up and I can take a look and let you know.

I am sorry ... Way up north in Durham

 

[Machine monkey]

Hi Mat I have just bought a Z3 2.8 .. Do you have any exhaust tips to fit this ? Thanks

I am sure I can make them your in oxfordshire right? If so we can meet up and I can take a look and let you know.

I am sorry ... Way up north in Durham

Well i am sure i can still help out. I sent you a PM

 

[Machine monkey]

Ok guys i am starting the one set tonight. If you would like a set let me know today. As it would make it easier for me

 

[Machine monkey]

No no more interest?
Crazy busy then nothing. I guess that's the market saturated!!