Spring todo list - [Electric seats are in]

M

MrPT

Veteran
 Bucks/Oxon
Site Supporter
1. First, some "keen" driving - shame to waste the awesome weather... :driving:

2. ...then a much-needed clean (except the rear window - oops).

nq9xcx.jpg

2d1a5nd.jpg


3. Replaced a single missing torx bolt on the engine vanity cover. They don't serve any purpose apart from to annoy you when they wriggle free.

8zh4kh.jpg

2m5m5hs.jpg


4. Added strut tower covers. Hopefully these will stop the pond life growing in there.

9bja74.jpg

1585b45.jpg


5. Replaced my centre caps. They were the crappy sticker type before.

33pgj1k.jpg

xfq0pg.jpg


6. Used Gtechniq C4 on the exterior plastic trim. This stuff is amazing!

2ypkhtl.jpg

i6vzmh.jpg


That's all for now. Thought I'd create this thread to give me some motivation to get the rest of the list done:

  • Fit piano black trim
  • Fit heated electric seats
  • Replace roof motor
  • Clean Vanos solenoids
  • Paint calipers
  • Replace all disks and pads

Lots to do, but it feels good to make some progress after a miserable winter. :thumbsup:
 
GP06Roadster said:
Looking very nice MrPT :thumbsup: that Gtechniq gear looks very impressive, really smartens up that trim :)
Click to expand...

I was trying to get away with using peanut oil as a cheap solution. It's great - just doesn't last very long. The C4 is expensive but a few drops apparently go a long way.
 
Wow!

Very similar car, and VERY similar list of jobs to do!

Already got my new wheel centres, GTechnique C4 and IPA. Next on the list is brakes, spooky!
 
si-forks said:
TonyP said:
Where did you get the strut tower covers from please?
Click to expand...
+1

sent by galaxy S4 on tapatalk
Click to expand...

They are part number 31312229458. £6.75 inc VAT from Sopers.

They are a friction fit on the nuts so you really need to give them a whack to get them on properly, i.e. block of wood + hammer.
 
One heated electric seat is in!

Meant to fit both, but between the f1, mothers' day, WDS not working and the passenger side kick panel taking about an hour to refit (what's the secret?!), I ended up running out of our newly-extended daylight hours. :( Only managed to finish up by stealing a billion watt uplighter off my folks.

nudy8aha.jpg

e8enurys.jpg

It was the trickiest mod I've done so far. A lot of awkward lifting, dismantling and wiring, although the actual connections were fairly straightforward in the end. The electric adjustment is neat - my passengers never seemed to get on with the manual controls. Always lots of crashing and banging. :?
 
Right, the other one is in, after another half day of abandoning my family. :? :D

The driver's side was still not particularly straightforward, even after completing the passenger's side, and it was very awkward doing all the loom work in the footwells. I would still recommend it if you have heated manual seats and fancy a bit of DIY - the required skill level is moderate but nothing special. The heated electric seats seem to be about the same price to buy/sell on ebay and don't weigh much more (this was a surprise, actually).

If you do anything like this, remember to disconnect the battery at least 20 mins before removing the seats!

Old seat out:

9amrdt.jpg


Footwell trim off:

2q2ljrl.jpg


New wires (power, ground and the K-Bus connection) inserted into the under-seat connector:

25qahpw.jpg


Wires tidied up and plumbed into the existing harness guide under the drivers seat:

s3ivqo.jpg


Ground soldered onto a ring terminal and connected to the common grounding point behind the kick panel:

vy8mts.jpg


24y9qwl.jpg


Power and K-Bus connections plumbed along the main wiring harness from the driver's side to the passenger side and out into the fuse box (the power is the light blue cable - temporarily secured using electrical tape as I need to swop it for thicker wire of the correct colour):

suvx5i.jpg


Here's the fully populated connector (in purple/pink on the bottom RHS of the fuse box) showing the top left - driver's side - and bottom left - passenger's side - power wires slotted into place:

qywoxg.jpg



Must do a proper How-To post at some point. For now, here are my notes from the installation:

  • Seat bases have 16mm nuts/bolts
  • This post from WestCDA has details of the required connector part numbers and other useful info
  • The under-seat connector (driver's side) pins are:
    15 - K-Bus (red/white striped plus yellow dots)
    14 - ground (brown)
    13 - power (red)
  • The fuse box connector is X11004 (for driver's and passenger's sides) and the pins are:
    10 - driver's power, fuse 29
    5 - passenger's power, fuse 15
  • 17A wire for power and ground (approx 12ga) and 5A wire (approx 18ga) for K-Bus

I still need to patch in the K-Bus connection somewhere - maybe the centre console switch panel.
 
MrPT said:
Right, the other one is in, after another half day of abandoning my family. :? :D

The driver's side was still not particularly straightforward, even after completing the passenger's side, and it was very awkward doing all the loom work in the footwells. I would still recommend it if you have heated manual seats and fancy a bit of DIY - the required skill level is moderate but nothing special. The heated electric seats seem to be about the same price to buy/sell on ebay and don't weigh much more (this was a surprise, actually).

If you do anything like this, remember to disconnect the battery at least 20 mins before removing the seats!

Old seat out:

9amrdt.jpg


Footwell trim off:

2q2ljrl.jpg


New wires (power, ground and the K-Bus connection) inserted into the under-seat connector:

25qahpw.jpg


Wires tidied up and plumbed into the existing harness guide under the drivers seat:

s3ivqo.jpg


Ground soldered onto a ring terminal and connected to the common grounding point behind the kick panel:

vy8mts.jpg


24y9qwl.jpg


Power and K-Bus connections plumbed along the main wiring harness from the driver's side to the passenger side and out into the fuse box (the power is the light blue cable - temporarily secured using electrical tape as I need to swop it for thicker wire of the correct colour):

suvx5i.jpg


Here's the fully populated connector (in purple/pink on the bottom RHS of the fuse box) showing the top left - driver's side - and bottom left - passenger's side - power wires slotted into place:

qywoxg.jpg



Must do a proper How-To post at some point. For now, here are my notes from the installation:

  • Seat bases have 16mm nuts/bolts
  • This post from WestCDA has details of the required connector part numbers and other useful info
  • The under-seat connector (driver's side) pins are:
    15 - K-Bus (red/white striped plus yellow dots)
    14 - ground (brown)
    13 - power (red)
  • The fuse box connector is X11004 (for driver's and passenger's sides) and the pins are:
    10 - driver's power, fuse 29
    5 - passenger's power, fuse 15
  • 17A wire for power and ground (approx 12ga) and 5A wire (approx 18ga) for K-Bus

I still need to patch in the K-Bus connection somewhere - maybe the centre console switch panel.
Click to expand...

holy sh*t glad mine has elec heated seats stock lol
 
Hello there

I was just wondering where you got your wheel badges from? Are they genuine BMW ones? Mine could also do with being replaced.

Cheers,

Jon.
 
JonBooth said:
Hello there

I was just wondering where you got your wheel badges from? Are they genuine BMW ones? Mine could also do with being replaced.

Cheers,

Jon.
Click to expand...

No, not genuine. As much as I don't like using non-OE parts, these aren't far off, quality-wise, and the genuine centre caps are 4x the price!

http://pages.ebay.com/link/?nav=item.view&id=301081308792

I'll replace them with proper ones if they tarnish quickly. The part number is 36136783536, FYI.
 
this is awesome, i am in the process of doing this, how did you take apart the passenger side so you could get to the purple connector? i have taken out all the screws and cannot get the body panel to come out.
 
raptor_demon said:
this is awesome, i am in the process of doing this, how did you take apart the passenger side so you could get to the purple connector? i have taken out all the screws and cannot get the body panel to come out.
Click to expand...

Have you removed the glove box?
 
You must log in or register to reply here.
Back
Top Bottom