Blanked out cluster lights

G

Gil1813

Member
Hi everyone,
A brief intro about the zed bought last year.
2003 m54 2.5 manual with only 53000 miles on car on the outside is pretty good but needed a little tlc.
Nothing showed up on test drive or when looking around it.
Now after trying to work through the jobs I'm coming across what's underneath.
Various fault codes relating to abs and DSC, but no lights on the dash, on removal of the cluster unit someone previously has blanked out both traction light and abs light.
I changed the yaw sensor yesterday for a same part number unit (second hand) but no chance light still there and codes will not clear
Codes 5e15 5e30 5e38
My other issue is I'm starting to think tha abs module is either faulty or the wrong one as the part number doesn't seem correct.
Any help much appreciated
Thanks
 
Welcome to the forum and I’m sorry to hear your problems, by the sounds of things whoever had the car previously either couldn’t find the problem or it’s an expensive fix, either way there a several members on here that will be able to help you get this resolved and hopefully cheaply.
 
I have previously helped another forum member to fix a 5E30 code, which was really hard to figure out but an easy fix in the end. Worth trying the fix if you have INPA (or can find a local member who has it) before spending good money on components.

https://z4-forum.com/forum/viewtopic.php?t=137461. (Skip to the end for a write up).

Good luck.
 
Also, check this thread where [ref]enuff_zed[/ref] fixed 5E30 and 5E38 by replacing the ABS speed sensor on the left front wheel (easy peasy).

https://z4-forum.com/forum/viewtopic.php?p=1843669
 
Zedebee said:
Also, check this thread where [ref]enuff_zed[/ref] fixed 5E30 and 5E38 by replacing the ABS speed sensor on the left front wheel (easy peasy).

https://z4-forum.com/forum/viewtopic.php?p=1843669
Click to expand...
Googling the codes shows yaw sensor (but you've done that), dsc unit, or rear left wheel sensor (not that if your speedo still works).
It is possible the old yaw sensor failed due to damp under the carpet. In which case I would double check there is no corrosion on the plug pins.
I had an Autophix 5900 code reader which told me exactly which of the four wheel sensors was the issue.
It could be that one is sending a spurious signal (or no signal) which is showing as an issue within the DSC unit instead.
 
Thanks guys,

Thing is the damn car has really got under my skin and I just can't see it not right, so I'll keep chipping away at the various issues to get it sorted.
This place is great because of the like minded people.

I did get a autophix 7910 after reading a few of your recommendations Enuff zed, but tech is not my thing so maybe I'm not using it correctly??
With regards the yaw sensor the car has been in the garage since iv had it so definitely now dry, but when removing the seat to get it out there has been damp/wet down there, the runners are all rusty on the carpet and the yaw sensor was very corroded.
I've replaced it with same part number 34526759412 which was off a mini, hoping iv got the correct one ?

Although frustrating I do enjoy the challenge, sometimes :headbang:
 
Gil1813 said:
Thanks guys,

Thing is the damn car has really got under my skin and I just can't see it not right, so I'll keep chipping away at the various issues to get it sorted.
This place is great because of the like minded people.

I did get a autophix 7910 after reading a few of your recommendations Enuff zed, but tech is not my thing so maybe I'm not using it correctly??
With regards the yaw sensor the car has been in the garage since iv had it so definitely now dry, but when removing the seat to get it out there has been damp/wet down there, the runners are all rusty on the carpet and the yaw sensor was very corroded.
I've replaced it with same part number 34526759412 which was off a mini, hoping iv got the correct one ?

Although frustrating I do enjoy the challenge, sometimes :headbang:
Click to expand...
Should be the silver metal one? If it's black plastic you have a facelift version which isn't compatible.
I would take the time to double check the connector just in case.
 
I had an airbag fault code on my car for over a year that I wasn't aware of as a previous owner had blanked out the light too, mine was a simple fix cleaned the connections under the seat with electrical contact cleaner and haven't had the fault since, cleaning connections this way has rectified other faults I've had on the car too, so everytime I disconnect anything on the car now I clean it with contact cleaner.
 
Have you checked realoem parts site for the correct part number that was fitted to your car using the last 7 of your Vin number?
Here is a link to my 2003 2.5 showing the ABS parts but do check using your Vin number.
https://www.realoem.com/bmw/en/showparts?id=BT32-EUR-07-2003-E85-BMW-Z4_25i&diagId=34_1308
 
Thanks everyone,

Yes the old and new yaw sensor are both metal silver ones.
Have given all the contacts a good soaking with wd40 and still codes appear.
I'm clearing the codes on the autophix but they are still showing when checking again.
Colb- funny thing is with part checker when I put my vin in it says no parts available on yaw sensor page only ??

Enuff zed- can the silver metal ones still work regardless of part numbers?
 
Gil1813 said:
Thanks everyone,

Yes the old and new yaw sensor are both metal silver ones.
Have given all the contacts a good soaking with wd40 and still codes appear.
I'm clearing the codes on the autophix but they are still showing when checking again.
Colb- funny thing is with part checker when I put my vin in it says no parts available on yaw sensor page only ??

Enuff zed- can the silver metal ones still work regardless of part numbers?
Click to expand...
I believe they do but I’ve only ever used other Z4 hones.
 
Couldn't find the part number you posted on Realoem but did find a youtube video on replacing the yaw sensor under the carpet here https://www.youtube.com/watch?v=dSfCw3-8zz0
Not much use as you have already been through this but may help others reading this thread.
 
This is the exact part that I got, it does look in good condition, but could it be still faulty as it is a used one ??
Is there anyway of checking to see if faulty?

Colb- I have found the part number on part checker it show 2 diagrams for the brake system, and only gives details on the second diagram. Also part number on that is not the same as the one I bought.
Th
 

Attachments

  • 1703341051140.jpg
    1703341051140.jpg
    106.6 KB · Views: 352
In terms of coding they are plug and play but I've seen lots of posts suggesting that if you have issues then they need recalibrating.
 
Just had another look at Realoem parts site using my 2003 2.5 Vin number, mine has this one fitted
https://www.realoem.com/bmw/en/showparts?id=BT32-EUR-07-2003-E85-BMW-Z4_25i&diagId=34_1308
If there are two diagrams just use the one that lists the parts and part numbers the other will tell you no parts fitted to your car.
If you click on the part number it will display all other models the item is fitted to, suspect the replacement you have is not compatible with your car. Best find another good replacement with the part number listed in Realoem or one of the units that have superseded the original.
 
Well I've just changed the yaw sensor for another one with tha same part number as per realoem listed for my vin number.
No change really, I changed the sensor then plug in the scanner with 3 codes appearing, 5e15, 5e30, 5e38, when I try to erase them only the 5e15 goes, but then reappears when the ignition is turned off and back on.
When I try to recalibrate the speed sensor with the autophix it comes up connection error, could it be a wiring issue and not connecting?
The abs dsc unit is clicking every few seconds?? Is that normal?
Could the battery cause any issues as I'm not sure it's at its best although I'm keeping the charge on with a battery maintainer.
I hoping you guys can maybe point me in the next direction to go.
Thanks.
 
You must log in or register to reply here.

Similar threads

D
Nearside rear LED failure on light cluster
Replies
3
Views
399
Dr_Tripwire
D
D
E85 Facelift N/S rear light cluster
Replies
2
Views
257
davep10000
D
G
Light cluster - Bulb identification
Replies
10
Views
535
Scooba_Steve
S
B
Want Cluster Lights to Come on With Engine Start
Replies
5
Views
386
enuff_zed
enuff_zed
P
coding replacement clocks (instrument cluster)
Replies
5
Views
271
paul__mck
P
Back
Top Bottom