OK so ive been and got some pressed plates, now they look fine but ive noticed that there is no suppliers name or address underneath. they are just blank with my reg number. is this a big thing where i am likely to be pulled over every ten minutes?
Pressed Plates
- Thread starter Nova2k7
- Start date
Depends how obviously non standard they are and how eagle eyed the plod are.
There is a full standard on plates. even if the font is ok, the yellow/white back ground has to meet a certain standard for reflectivity - this is probably where you'll fail.
Plenty of people run with non standard font or no front plate. think they might be cracking down though.
There is a full standard on plates. even if the font is ok, the yellow/white back ground has to meet a certain standard for reflectivity - this is probably where you'll fail.
Plenty of people run with non standard font or no front plate. think they might be cracking down though.
BSAU 145D
The British Standard sets out the physical characteristics on the number plate. This includes:
Visibility
Strength
Reflectivity
The British Standard also requires that a number plate must be marked with the following information: -
The British Standard Number (currently BS AU 145d)
The name, trade mark, or other means of identification of the manufacturer or component supplier. (The company who actually make the number plate.)
The name and postcode of the supplying outlet. (The 'supplying outlet' is taken to mean a company whose business consists wholly or partly of selling number plates.)
A non-reflective border and the Euro-symbol with the national identification letters are optional additions.
There shall be no other markings or material contained on the number plate.
Further information about the British Standards requirements can be obtained at www.bsi-global.com.
But when all said and done I have just had my MOT carried out and plates carry no BS number or any other info but the spacing, font etc is all legal and not a word was said. Guess it just depends on how eagle eyed the plod are.
The British Standard sets out the physical characteristics on the number plate. This includes:
Visibility
Strength
Reflectivity
The British Standard also requires that a number plate must be marked with the following information: -
The British Standard Number (currently BS AU 145d)
The name, trade mark, or other means of identification of the manufacturer or component supplier. (The company who actually make the number plate.)
The name and postcode of the supplying outlet. (The 'supplying outlet' is taken to mean a company whose business consists wholly or partly of selling number plates.)
A non-reflective border and the Euro-symbol with the national identification letters are optional additions.
There shall be no other markings or material contained on the number plate.
Further information about the British Standards requirements can be obtained at www.bsi-global.com.
But when all said and done I have just had my MOT carried out and plates carry no BS number or any other info but the spacing, font etc is all legal and not a word was said. Guess it just depends on how eagle eyed the plod are.
Greeno said:
Sorry I should have made it a bit clearer my plates are brand new, I replaced them after fitting my new bumpers, but I take your point about it being hard to inforce retrospectively, i have just quoted the current regs with regards to legality.
Had them on my z3 upto a year or so ago .Never pulled over,plates have correct Font & Spacing.Plates could have been made a few years ago & therefore don`t need postcode. 
Greeno said:
It will also apply to any replacement plate fitted to the car after the regulations came into effect. You may get away with an obviously old plate on an old car (pre September 2001) but not new plates on an old car.
I don't even think pressed plates are legal since 2001 given that the regulations preclude 'any design, pattern or texture' or even the appearance of same.
Just been party to a long thread on a Jag forum where an owner has been ticketed for having 3D effect font on an otherwise 100% legal plate. Had to have new plates, MOT centre verification then off to the police with proof and pay his fine
As with all things like this you may drive for years and not be stopped or be pulled tomorrow. Personally I'd bin them and be legal and avoid the opportunity to be pulled.