Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.
Passenger one touch window not working up
-
- Newbie
- Posts: 31
- Joined: Sat Oct 30, 2021 9:28 am
Passenger one touch window not working up
Morning folks,
I can't work out why my one touch up doesn't work on the passenger side. I've got it working on the drivers side by running it down to the bottom, holding it for 10 secs and then backup and hold for 10 seconds
Am I missing a trick somewhere?
I can't work out why my one touch up doesn't work on the passenger side. I've got it working on the drivers side by running it down to the bottom, holding it for 10 secs and then backup and hold for 10 seconds
Am I missing a trick somewhere?
- enuff_zed
- Lifer
- Posts: 14702
- Joined: Wed Oct 26, 2016 11:05 am
- Location: Attleborough, Norfolk
Passenger one touch window not working up
I have 3 E85s here at the moment. None of them will do one touch up on the passenger side.
I believe its a 'feature'.
I believe its a 'feature'.
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
I may be wrong but I am sure it is a codable option, certainly on the post facelift. It may just need enabling with NCS/Carly.
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.
- DMike
- Senior Member
- Posts: 2440
- Joined: Tue Sep 11, 2007 7:15 pm
Passenger one touch window not working up
When doing the reset, you need to hold the switch until the faint clicking sound, 10 sec may be too long. I remeber there was a thread with an alternative reset sequence too.
2005 Z4 3.0i Sterling grey
- enuff_zed
- Lifer
- Posts: 14702
- Joined: Wed Oct 26, 2016 11:05 am
- Location: Attleborough, Norfolk
Passenger one touch window not working up
Pretty certain the reset won't achieve that though. God knows I've tried enough times
I think Scooba_Steve may be correct and it needs coding?
- DMike
- Senior Member
- Posts: 2440
- Joined: Tue Sep 11, 2007 7:15 pm
Passenger one touch window not working up
Could be that too and pre 4/2004 might still be out of luck, says some posts. The alternative reset was with doors closed, open window fully and immediately click open four times within 10 seconds. Then do the conventional close window and holding wait for click, open window and holding wait for click, close window anf holding wait for click -sequence.
2005 Z4 3.0i Sterling grey
- patriot66
- Lifer
- Posts: 3478
- Joined: Sun Jan 11, 2015 2:59 am
- Location: Mawdesley, Lancashire
Passenger one touch window not working up
My car is May'03 build and I had passenger one touch window, 5mph central door locking, indicator flash and beep when locking/unlocking and hood open/close from keyfob all coded last year, I think with ISTA
Sterling Grey '03 2.5i SE / Infinitas Supercharger / S.M.G / Hardtop / Gloss Black 162s / Bilstein B4s / 3.0i Brakes / DLV De-Cat & Silencer / Rebuilt VANOS / Sonar 2Xcite Lights / Carbon & Alcantara Trim / M-Sport Seats / ...& Side Covers !
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
Thanks for confirming my brain still works
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
Notes on initializing power window unit (from 04/2004)
Warning!
Danger of injury!
There is no anti-trapping protection during initialization.
Note:
Cars built prior and up to 04/2004 have no anti-trapping protection and on the passenger side no toll closing function.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
Initialization with engine running
Convertible top, doors and windows closed
Initialization comprises:
Erasure of initialization
Reinitialization
An initialization must be performed:
In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
After the power window drive has been replaced
After work is carried out on the power window mechanism
After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
After the door window glass has been removed and installed or replaced
After adjustment work on the door window glass
After adjustment work on the convertible top
After replacement of seals
Erasure of initialization:
Open door window glass fully
Operate power window switch in ”Open” position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
This completes initialization.
Note:
Carry out function check (one-touch control function, anti-trapping protection and, if necessary, comfort function).
Warning!
Danger of injury!
There is no anti-trapping protection during initialization.
Note:
Cars built prior and up to 04/2004 have no anti-trapping protection and on the passenger side no toll closing function.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
Initialization with engine running
Convertible top, doors and windows closed
Initialization comprises:
Erasure of initialization
Reinitialization
An initialization must be performed:
In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
After the power window drive has been replaced
After work is carried out on the power window mechanism
After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
After the door window glass has been removed and installed or replaced
After adjustment work on the door window glass
After adjustment work on the convertible top
After replacement of seals
Erasure of initialization:
Open door window glass fully
Operate power window switch in ”Open” position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
Open door window glass fully
Operate and hold power window switch in ”Close” position (second switch stage)
Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
This completes initialization.
Note:
Carry out function check (one-touch control function, anti-trapping protection and, if necessary, comfort function).
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.
- enuff_zed
- Lifer
- Posts: 14702
- Joined: Wed Oct 26, 2016 11:05 am
- Location: Attleborough, Norfolk
Passenger one touch window not working up
Well there's my answer then.Scooba_Steve wrote: ↑Sun Nov 28, 2021 12:47 pm
Note:
Cars built prior and up to 04/2004 have no anti-trapping protection and on the passenger side no toll closing function.
Need to buy a newer one.
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
Just because BMW say so, doesn't mean they're always right
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.
- BumpyZ4
- Member
- Posts: 589
- Joined: Mon Feb 17, 2020 8:05 pm
- Location: New Orleans, LA USA
Passenger one touch window not working up
I have a 2003 E85 and the one touch windows (up and/or down) have to be coded. Coded mine and they both work fine.
2003 E85 3.0i Sterling Gray
KLR 650
Diva Roadster (Kit Car)
KLR 650
Diva Roadster (Kit Car)
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
Well worth trying for the early models.
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.
- 1000rr
- Senior Member
- Posts: 1057
- Joined: Thu Oct 13, 2016 10:53 pm
Passenger one touch window not working up
Yup, all e85 models can be coded to offer one touch on all windows.
-
- Lifer
- Posts: 5277
- Joined: Wed Feb 19, 2014 3:01 pm
- Location: NW London
Passenger one touch window not working up
Isn't it odd that BMW don't say that. Thankfully easy to prove them wrong!
3.0si Sport: F10 Illuminated ZHP, Retrofit Cruise, OE Stubby, Gaptech RCH+, Kenwood BT73DAB + Handsfree, HIDs, LED Sidelights, OE LED Number Plate Lights, Custom LED strip bootlight.