Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.

Rod bearing failure - what to do?

"M" Specific discussion
Post Reply
User avatar
BMWZ4MC
Lifer
Lifer
Posts: 6335
Joined: Sun Sep 13, 2009 4:24 pm
Location: Back in the sunshine

Rod bearing failure - what to do?

Post by BMWZ4MC » Thu Mar 14, 2019 4:17 am

Hi John, as Lower has said there have been occasional reports of the F20C spinning a bearing, but it’s rare. There was a period when S2000s were very cheap cars and I suspect a few were neglected for periods of their life. Since most consume oil, it’s actually surprising that more haven’t had problems.
Image
Z4MC - heavily fettled for track use
Lotus Exige - sensible daily driver on the mods slippery slope
Westfield SEiW - in hibernation
Modified RS4 Avant - back in Blighty
S2000 GT - gone

Gwest44
Member
Member
Posts: 919
Joined: Thu Aug 30, 2018 10:13 pm
Location: Sheffield

Rod bearing failure - what to do?

Post by Gwest44 » Thu Mar 14, 2019 9:13 am

As has already been said this makes for s**t reading and I feel for the OP’s that have been effected - in addition I’m now shitting myself thinking that mine might go at anytime now I’m about to reach 100k.

Excuse my ignorance and inabity to extract the relevant detail but if I take the car to my independent what should I be asking him to do to reduce the probability of this happening on mine - he did my inspection II 2,000 miles ago but would appear this is irrelevant as a deterrent to the issue?
Sapphire Black 23i
Previously 7xZ3's, 5xE85's, 2xE86's & 3xE89's

User avatar
mr wilks
Legend
Legend
Posts: 21893
Joined: Wed Jul 04, 2012 10:02 pm
Location: Lancashire

Rod bearing failure - what to do?

Post by mr wilks » Thu Mar 14, 2019 9:31 am

Gwest44 wrote: Thu Mar 14, 2019 9:13 am As has already been said this makes for s**t reading and I feel for the OP’s that have been effected - in addition I’m now shitting myself thinking that mine might go at anytime now I’m about to reach 100k.

Excuse my ignorance and inabity to extract the relevant detail but if I take the car to my independent what should I be asking him to do to reduce the probability of this happening on mine - he did my inspection II 2,000 miles ago but would appear this is irrelevant as a deterrent to the issue?
Put simply the only way for peace of mind is have the bearing shells replaced as a matter of routine maintenance , circa £1k job , opening the bottom end up just to check them then putting the originals back is not really viable :(

Thread here might be worth a read viewtopic.php?f=9&t=95781 :thumbsup:
3 ZMRs
3 E89s
5 Si coupes
5 Si roadsters
997 C4
TTRS
F82 M4
MK7 Golf Gti
current Bmw 6 Gran Turismo

User avatar
tomscott
Lifer
Lifer
Posts: 7466
Joined: Mon Sep 19, 2011 12:26 pm
Location: Manchester
Contact:

Rod bearing failure - what to do?

Post by tomscott » Thu Mar 14, 2019 9:49 am

Its not the smallest job so makes sence to have other jobs done at the same time.

Mounts, bolts etc

I wouldn't be panicking this happens on a rare basis and there are so many different factors that its impossible to give an indication on what each cars wear it like unless you have owned the car since new.

Ive been here for 8 years and have seen there has been around 6-7 instances, its a forum people come here for these types of problems so its not common. On the other hand these cars are hitting bigger milage now.

Just add it to the next round of maintenance.

User avatar
Jembo
Lifer
Lifer
Posts: 6030
Joined: Sat Jun 25, 2011 11:59 pm
Location: 1066 Country

Rod bearing failure - what to do?

Post by Jembo » Thu Mar 14, 2019 10:14 am

I’d also check how often they’d done it before - every so often or known for undertaking it regularly without neg feedback.

I’m also not clear whether there are now recommended upgraded shells / bolts that are available (the ones lined with tin mentioned in video instead of copper) or whether stick to OEM

Cheers
Joined the dark side with a ///M Hell Bronze Sepang Coupe :happyclap:
Ex Aug 2005 Maldives Blue 3 litre cruizer, lots of toyz,

Lifer 54

User avatar
exdos
Senior Member
Senior Member
Posts: 2789
Joined: Wed Feb 22, 2012 12:58 am

Rod bearing failure - what to do?

Post by exdos » Thu Mar 14, 2019 10:50 am

In view of the fact that the bearings shells of most S54 engines, of which there are 12 parts per engine, will show signs of pitting/scoring after the engine has done significant mileage, the fact remains that only a very small number of bearings actually fail catastrophically (i.e. only 2 bearing shells per failed engine), would suggest to me, at least, that this is not, itself, the fundamental cause of bearing shell failure/destruction.

OTOH, how would the failure of the connecting rod bolts, by stretching beyond tolerance, manifest itself other than by permitting the crankshaft to hammer the bearing shells into much thinner pieces?

IMO, if you're going to inspect the bearing shells, then you should also commit to changing them AND the con-rod bolts for new upgraded parts.

A bad gear shift, say, into 2nd gear instead of 4th, would also be an occasion which could cause catastrophic bearing shell failure.
Last edited by exdos on Thu Mar 14, 2019 10:54 am, edited 1 time in total.

User avatar
ph001
Lifer
Lifer
Posts: 3870
Joined: Mon Oct 31, 2016 5:53 pm
Location: N. Yorkshire.

Rod bearing failure - what to do?

Post by ph001 » Thu Mar 14, 2019 10:52 am

tomscott wrote: Thu Mar 14, 2019 9:49 am Ive been here for 8 years and have seen there has been around 6-7 instances, its a forum people come here for these types of problems so its not common. On the other hand these cars are hitting bigger milage now.
Quite true, also a good indicator is how many instances there are of it over on M3Cutters. There are 1000+ S54 M owners on there and reports of failures are under 1%.
2007 E85 Z4 3.0Si manual :driving:
19" CSL's | Eibach Springs | Aeroskirts | Z4M front bumper | Clear brake light | ZHP | RCH+| Stubby

2004 E46 M3 coupe manual - gone but not forgotten.

Image

User avatar
R60BBA
Senior Member
Senior Member
Posts: 1776
Joined: Sat Sep 30, 2017 7:53 pm
Location: London, United Kingdom

Rod bearing failure - what to do?

Post by R60BBA » Thu Mar 14, 2019 2:28 pm

tomscott wrote: Thu Mar 14, 2019 9:49 am Its not the smallest job so makes sence to have other jobs done at the same time.

Mounts, bolts etc

I wouldn't be panicking this happens on a rare basis and there are so many different factors that its impossible to give an indication on what each cars wear it like unless you have owned the car since new.

Ive been here for 8 years and have seen there has been around 6-7 instances, its a forum people come here for these types of problems so its not common. On the other hand these cars are hitting bigger milage now.

Just add it to the next round of maintenance.
It’s not rare, in fact it’s becoming more common.

Unless you have owned the car from new, it’s impossible to know how it has been looked after by former keepers.

£1,000 to get this sorted isn’t a big deal and should be done on any car over 70,000 miles. If you cannot afford this then you should not be driving one of these.
Current: 2002 E46 M3
Current: 2004 R53 Cooper S
Current: 2005 997 Carrera S
Gone: 1998 E31 840Ci Sport
Gone: 2007 Z4 E86 3.0Si Sport
Gone: 2001 Z3 E36/7 2.2i San Remo Individual
Gone: 2015 F21 116d M Sport
Gone: 2012 A3 Sportback 1.2TFSI

User avatar
tomscott
Lifer
Lifer
Posts: 7466
Joined: Mon Sep 19, 2011 12:26 pm
Location: Manchester
Contact:

Rod bearing failure - what to do?

Post by tomscott » Thu Mar 14, 2019 2:59 pm

It depends who you talk to as I said forums are places people bring these issues to light and obviously the Z4 is lower volume than the M3 but its certainly not common.

Same with Porsche I always thought it was internet scaremongering until I bought a car and 2 weeks later had a 12k bill for a rebuild...

That being said you still have to be very unlucky.

User avatar
R60BBA
Senior Member
Senior Member
Posts: 1776
Joined: Sat Sep 30, 2017 7:53 pm
Location: London, United Kingdom

Rod bearing failure - what to do?

Post by R60BBA » Thu Mar 14, 2019 3:16 pm

tomscott wrote: Thu Mar 14, 2019 2:59 pm It depends who you talk to as I said forums are places people bring these issues to light and obviously the Z4 is lower volume than the M3 but its certainly not common.

Same with Porsche I always thought it was internet scaremongering until I bought a car and 2 weeks later had a 12k bill for a rebuild...

That being said you still have to be very unlucky.
There’s a lot less Z4Ms than M3s and I’d even stipulate that as a 2 seater, they are more likely to have less miles on em than M3’s.

They are also up to 2 years younger than the last E46 M3s and 7 years younger than the first MK20s.

However they have the same engine and so the same thing can occur as per the unfortunate 2 examples in this very thread.

In my post I wasn’t just referring to examples on forums where people have posted about their rod bearing failures, but I was also taking into account discussions which I have had with various M specialist garages on this, who have all confirmed that it is becoming more common in recent years.

You also cannot ignore that MK20 M3s had this job done under recall, which affected thousands of cars...further reinforcing it has been a problem area from day 1.

I did mine for peace of mind. The shells came out clean and I could’ve waited another 30,000 miles or so however I could’ve been ‘unlucky’ as you put it and spun a bearing in 5,000 miles.

Either way I no longer have that worry as the job is done. Now my concern is the flippin’ boot floor. :roll:
Current: 2002 E46 M3
Current: 2004 R53 Cooper S
Current: 2005 997 Carrera S
Gone: 1998 E31 840Ci Sport
Gone: 2007 Z4 E86 3.0Si Sport
Gone: 2001 Z3 E36/7 2.2i San Remo Individual
Gone: 2015 F21 116d M Sport
Gone: 2012 A3 Sportback 1.2TFSI

User avatar
Bing
Legend
Legend
Posts: 26514
Joined: Sun Oct 02, 2011 7:19 pm
Location: Exiled Scot in Maidstone

Rod bearing failure - what to do?

Post by Bing » Thu Mar 14, 2019 3:53 pm

I better put mine up for sale because apparently I shouldn't be driving it, given it's on 83k, has not had the shells replaced and I don't have a spare grand right now ... I must also remember to knock £1k off the asking price because the shells have not been done, and I am sure that will become a common bargaining point in the near future :P

In all seriousness, based on everything everyone is saying, if you can afford to have this done by 70k (an arbitrary number by the way, with no empirical evidence presented or probably even possible to present) then you probably should. If you can't then budget to do it at about 80-100k and in the meantime pay attention to the car - regular interim oil & filter changes, on-time servicing, visual inspection, regular oil analysis, and treat the car with mechanical sympathy.

EDIT - sorry, I probably should have put a smiley face in here somewhere... Now corrected for tongue-in-cheek :lol:
Last edited by Bing on Thu Mar 14, 2019 5:00 pm, edited 2 times in total.
Current... Silver Grey ///M Roadster, non-flimper spec, Imola Red nappa, permanent ear-to-ear grin 8)

Previous... 3.0Si Sport Roadster, Black Sapphire, Dream Red leather with lots of toys and lots of mods...

mmm-five
Lifer
Lifer
Posts: 12714
Joined: Sun Nov 30, 2008 1:03 pm
Location: Liverpool
Contact:

Rod bearing failure - what to do?

Post by mmm-five » Thu Mar 14, 2019 4:46 pm

I think they should be done every Insp.II :P

That’s about 50-55,000 miles for daily drivers, or 40,000 miles for garage queens/weekend cars...and work out about £500 extra per year for daily drivers or £100/year for the rest.

Or about £50/year in my case (if you don’t include the cost of my replacement engine) :?


Whichever way you look at it, it’ll cost less than VED :thumbsup:
Trigger’s Z4MC
Some bits now over 163,000 miles, some less than 1,000 miles.
Individual Ruby Black, Individual extended champagne leather, plus many options

Image

User avatar
Bing
Legend
Legend
Posts: 26514
Joined: Sun Oct 02, 2011 7:19 pm
Location: Exiled Scot in Maidstone

Rod bearing failure - what to do?

Post by Bing » Thu Mar 14, 2019 4:54 pm

Ha, that's not necessarily a s**t idea. Funnily enough 100k will be around my second Insp 2. And as I have already said, that's what I'm budgeting towards.
Current... Silver Grey ///M Roadster, non-flimper spec, Imola Red nappa, permanent ear-to-ear grin 8)

Previous... 3.0Si Sport Roadster, Black Sapphire, Dream Red leather with lots of toys and lots of mods...

User avatar
R60BBA
Senior Member
Senior Member
Posts: 1776
Joined: Sat Sep 30, 2017 7:53 pm
Location: London, United Kingdom

Rod bearing failure - what to do?

Post by R60BBA » Thu Mar 14, 2019 5:07 pm

mmm-five wrote: Thu Mar 14, 2019 4:46 pm I think they should be done every Insp.II :P

That’s about 50-55,000 miles for daily drivers, or 40,000 miles for garage queens/weekend cars...and work out about £500 extra per year for daily drivers or £100/year for the rest.

Or about £50/year in my case (if you don’t include the cost of my replacement engine) :?


Whichever way you look at it, it’ll cost less than VED :thumbsup:
Well put 8)
Current: 2002 E46 M3
Current: 2004 R53 Cooper S
Current: 2005 997 Carrera S
Gone: 1998 E31 840Ci Sport
Gone: 2007 Z4 E86 3.0Si Sport
Gone: 2001 Z3 E36/7 2.2i San Remo Individual
Gone: 2015 F21 116d M Sport
Gone: 2012 A3 Sportback 1.2TFSI

mmm-five
Lifer
Lifer
Posts: 12714
Joined: Sun Nov 30, 2008 1:03 pm
Location: Liverpool
Contact:

Rod bearing failure - what to do?

Post by mmm-five » Thu Mar 14, 2019 5:28 pm

Once I’ve put my ‘new’ engine in (47k on it), the only original parts will be cats, bonnet, roof & gearbox.

If I’d done the rod bearings earlier, I would have still had a 140,000 mile old engine, but with new bearings...so you just know I’d be needing vanos, cams, rods, etc. shortly too.

This way I’ve now got a low mileage car again :P
Trigger’s Z4MC
Some bits now over 163,000 miles, some less than 1,000 miles.
Individual Ruby Black, Individual extended champagne leather, plus many options

Image

Post Reply