Machine Monkey exhaust tips question and photo request

Mangozac · Post by **Mangozac** » Wed Jan 24, 2018 10:17 pm

Machine monkey wrote: ↑Wed Jan 24, 2018 12:39 pm Not at all buddy.
I have seen your work on your exhaust system. I just want to clarify how I make them.
They are in the simplest terms just tube made to fit and finished nicely. The was just that i found it funny.

Sweet as

What you've done looks great and the 3" tip size suits the Z4M perfectly but I personally don't like that the tips end up touching. Obviously not much that can be done about it

Tcochrane92 · Post by **Tcochrane92** » Wed Jan 24, 2018 10:23 pm

Machine monkey wrote: ↑Wed Jan 24, 2018 1:27 pmYou will need to buy that yourself mate.

We briefly touched on this in our PM chat, but could you do one big tip and one small tip? like 3" & 2"? (I don't know what sizes would work)
Similar to this:

: rpi exhaust.jpg (115.35 KiB) Viewed 767 times

: rpi.jpg (93.88 KiB) Viewed 767 times

Machine monkey · Post by **Machine monkey** » Thu Jan 25, 2018 9:15 am

I am looking it to that for you Saturday when i can get over to my workshop.

Machine monkey · Post by **Machine monkey** » Thu Jan 25, 2018 9:21 am

Mangozac wrote: ↑Wed Jan 24, 2018 10:17 pm
Machine monkey wrote: ↑Wed Jan 24, 2018 12:39 pm Not at all buddy.
I have seen your work on your exhaust system. I just want to clarify how I make them.
They are in the simplest terms just tube made to fit and finished nicely. The was just that i found it funny.
Sweet as

What you've done looks great and the 3" tip size suits the Z4M perfectly but I personally don't like that the tips end up touching. Obviously not much that can be done about it

When sliding them over the original tips no. But when removing the old tips the fitting rings can be to move the tips left a bit and right a bit. So the fitting and outside are not concentric.

Mangozac · Post by **Mangozac** » Thu Jan 25, 2018 1:32 pm

Machine monkey wrote: ↑Thu Jan 25, 2018 9:21 am
Mangozac wrote: ↑Wed Jan 24, 2018 10:17 pm Sweet as

What you've done looks great and the 3" tip size suits the Z4M perfectly but I personally don't like that the tips end up touching. Obviously not much that can be done about it
When sliding them over the original tips no. But when removing the old tips the fitting rings can be to move the tips left a bit and right a bit. So the fitting and outside are not concentric.

Doesn't it look a bit odd if they're not concentric though? I've never actually seen close up shots of the tips fitted!

Tcochrane92 · Post by **Tcochrane92** » Thu Jan 25, 2018 2:08 pm

Machine monkey wrote: ↑Thu Jan 25, 2018 9:15 amI am looking it to that for you Saturday when i can get over to my workshop.

Not 100% sure whether I want one bigger than the other at this point mate, so don't do anything that'll cost please

Tcochrane92 · Post by **Tcochrane92** » Fri Jan 26, 2018 10:30 am

Machine monkey wrote: ↑Thu Jan 25, 2018 9:15 amI am looking it to that for you Saturday when i can get over to my workshop.

Are your MM 3.0si tips the same as the ///M tips?

Machine monkey · Post by **Machine monkey** » Fri Jan 26, 2018 10:33 am

Tcochrane92 wrote: ↑Fri Jan 26, 2018 10:30 am
Machine monkey wrote: ↑Thu Jan 25, 2018 9:15 amI am looking it to that for you Saturday when i can get over to my workshop.
Are your MM 3.0si tips the same as the ///M tips?

Nope.

Phoenixboy · Post by **Phoenixboy** » Fri Jan 26, 2018 3:43 pm

I have a set on order, and look forward to getting them fitted.
yes I know, some people are easily pleased.

Machine monkey · Post by **Machine monkey** » Thu Feb 01, 2018 2:51 pm

Tcochrane92 wrote: ↑Thu Jan 25, 2018 2:08 pm
Machine monkey wrote: ↑Thu Jan 25, 2018 9:15 amI am looking it to that for you Saturday when i can get over to my workshop.
Not 100% sure whether I want one bigger than the other at this point mate, so don't do anything that'll cost please

Don’t worry I won’t be doing anything. Not until full payment is received not aft what happened last time!!

Z4-forum.com

Z4-forum.com