- what you need
- torx 10 screwdriver
- trim tool
- soldering iron adjustable heat
- soldering wire
- acrylic paints: baby blue, red (only need very small amounts and gloss doesn't matter, go for color match)
- paint brush, size 4 or 6
- 16 white SMD LEDs (buy 20 to be on the safe side)
- 4 blue SMD LEDs (buy 10 in case you would want stronger blue look)
- watch this video to get a feeling of the task ahead and see how to remove the cluster from the car
- don't bother removing the steering wheel, just lower it all the way down
- go to 2:15 (post editor doesn't like setting starting time)
- how to do it
remove cluster front and needles- remove the 4 torx 10 screws from the cluster on the back
- using the trim tool remove the back cover (easier this way, than using a screwdriver)
- start on the right side, push the trim tool with the u-shape end into the clip and raise the cover
- repeat clockwise for the lower clips. do the top ones last
- IMPORTANT mark the position of the needles
- remove the 4 needles on the front using the trim tool as shown in the video (simply put a piece of paper under the tool, no need for taping)
- try not turning the needles while lifting upwards, so that their axes stay where they were, when you marked their position
prepare and paint the needles (so they dry out completely while replacing the LEDs)
- using the sanding paper remove the white film from the top and bottom parts of the needles completely
- paint only the bottom of the needles: bigger ones blue, smallers ones red
- also paint the part where the axis go into and around it, not only the needle part (sorry no pict), this will restrict the glowing effect around the axes
- this type of paint covers pretty good, but make sure you don't leave out spots, don't worry if the paint is thick
- don't worry about the sides getting paint, we'll remove it once the paint dried out
remove old and solder on new LEDs
- further disassemble the cluster as shown in the video, till you get access to the LEDs
- IMPORTANTmark the positives of the LEDs
- turn on the soldering iron, set the heat knob to upright position (12 o'clock) and wait at least 10 minutes, higher temperatures can damage the LEDs
- remove the LEDs, indicated below on the pict, as shown in the video (tip: open the image in a new tab to see it in original size)
- solder on the new LEDs as indicated above on the pict, watch out for the marks you made earlier for the LED positive sides
- go to your car and connect the cluster to check that all LEDs lit up as expected
almost there, hang on- assemble the cluster, so you can place back the needles
- by this time the paint on the needles dried out, better check to make sure
- the center part of the needle will have a different color, here's how to address (don't worry it'll look good, zoomed in on the pictures)
- clean the sides of the needles from excess paint, you can use e.g. a carpet cutter to scrape off the paint gently
- place the needles back, watch for their positions to match the marks you made earlier
assemble the cluster, put it back and turn on the ignition
Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.
how to - instrument cluster color mod
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
Last edited by tintoverano on Mon Mar 30, 2020 6:15 pm, edited 1 time in total.
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
just updated the how to
missed out an important step fixing the issue with the center of the blue needles getting a different color, if this step is not done
missed out an important step fixing the issue with the center of the blue needles getting a different color, if this step is not done
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Senior Member
- Posts: 2716
- Joined: Fri Jun 21, 2019 10:06 am
- Location: Costa Del Sol
how to - instrument cluster color mod
I have ordered some SMD LED chips in order to do this mod, whilst I am waiting for those to arrive I removed the cluster today to have a look at the impending job. Those LED chips on the PCB are tiny, I guess you need a steady hand with the soldering iron and a magnifying glass According to some of these videos the SMD LED chips are 3528 / 1210. Is that the type you used? I managed to clean the central LCD screen whilst I had everything apart. Decided to go for all white LEDs including the central LCD as per the video you posted above, might colour the needles red.
2009 sdrive30i auto Sapphire Black / Coral Red
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
you can find out about the LEDs above in the "What you need" sectionSilverstar wrote: ↑Mon Mar 30, 2020 5:42 pm According to some of these videos the SMD LED chips are 3528 / 1210. Is that the type you used?
good luck
(while I'm here, I found photos about painting the needles, adding them for more clarity)
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Senior Member
- Posts: 2716
- Joined: Fri Jun 21, 2019 10:06 am
- Location: Costa Del Sol
how to - instrument cluster color mod
In the what you need section it just says 16 white and 4 blue SMD LEDs but it doesn't say which type of SMD e.g. 5050 2835 etc. After watching some more videos on YouTube about this I gather it is the 3825 / 1210 that are used, I imagine that is what you used?
2009 sdrive30i auto Sapphire Black / Coral Red
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
the grey text is a link for each type, just click on them
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Senior Member
- Posts: 2716
- Joined: Fri Jun 21, 2019 10:06 am
- Location: Costa Del Sol
how to - instrument cluster color mod
Perfect thanks! I didn't realise they were links....doh!
2009 sdrive30i auto Sapphire Black / Coral Red
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Member
- Posts: 490
- Joined: Thu Jun 11, 2020 12:45 pm
- Location: Swindon
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
I think it would
the LEDs are placed differently, other than that it should work
the LEDs are placed differently, other than that it should work
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Member
- Posts: 490
- Joined: Thu Jun 11, 2020 12:45 pm
- Location: Swindon
how to - instrument cluster color mod
I was afraid of that. For those that are gifted in electrics this may seem simple but I am nottintoverano wrote: ↑Mon Jun 22, 2020 11:24 am I think it would
the LEDs are placed differently, other than that it should work
May need to pop over to the E85 side and ask if anyone could provide any input.
What you've done looks amazing btw. Very impressed!
Maldives Blue 2.5i E85
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
take the cluster apart and make a photo of the printed circuit, where the LEDs are, no magic hereDr. Zed wrote: ↑Mon Jun 22, 2020 11:41 amI was afraid of that. For those that are gifted in electrics this may seem simple but I am nottintoverano wrote: ↑Mon Jun 22, 2020 11:24 am I think it would
the LEDs are placed differently, other than that it should work
May need to pop over to the E85 side and ask if anyone could provide any input.
thanks
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Member
- Posts: 490
- Joined: Thu Jun 11, 2020 12:45 pm
- Location: Swindon
how to - instrument cluster color mod
Sounds relatively simple when you put it like that!
Issue I have then is whether the LEDs you linked will be the correct ones so definitely need to do some more digging into this but I don't like the orange so it needs to go.
Issue I have then is whether the LEDs you linked will be the correct ones so definitely need to do some more digging into this but I don't like the orange so it needs to go.
Maldives Blue 2.5i E85
- tintoverano
- Member
- Posts: 666
- Joined: Wed Jan 09, 2019 4:33 pm
how to - instrument cluster color mod
I'm sure the LEDs are the same across models for the E series
mSport 23i
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
Coding Help, Stubby, Remap, K&N filter, Cruise Ctrl, Reverse cam, Instrument Cluster Color, UR front brace, CDV delete, Android on CIC, Roof Module, LSD
-
- Member
- Posts: 490
- Joined: Thu Jun 11, 2020 12:45 pm
- Location: Swindon
how to - instrument cluster color mod
I would like to think so mate, although your model is a lot newer than mine. It's not necessarily the model, but rather the year that would make me worried about differences in LEDs. I'll do some more research and see though. Looks like a fun mod with a massive impact on the feel of the car.tintoverano wrote: ↑Mon Jun 22, 2020 12:01 pm I'm sure the LEDs are the same across models for the E series
Maldives Blue 2.5i E85