Piano Black Style Dash & Console replacement

Chenti · Post by **Chenti** » Mon Aug 13, 2018 6:45 am

Piano Black Trim looks really so much better than the Silver/Ali imo. This is one thing I don’t need to look for on the new purchase then if it can be retro done on a drive out one day

Good service. Hope to be in touch in due course

Number5 · Post by **Number5** » Mon Aug 13, 2018 7:19 pm

Hi Chaps
Sorry, I've only just seen the recent posts Yeah, happy to do a PX on it still
As long as it's only surface marks and not bent or dented.

I'm busy for a few weekends but ok end of the month onwards

Number5 · Post by **Number5** » Tue Mar 12, 2019 12:11 pm

I carried out a Dash swap and fit for Tadek on the weekend. I forgot to take a Before photo but did remember a During & After picture.

: IMG_3740.JPG (322.54 KiB) Viewed 2769 times

: IMG_3744.JPG (276.83 KiB) Viewed 2769 times

: IMG_3745.JPG (248.57 KiB) Viewed 2769 times

gerryp · Post by **gerryp** » Fri Mar 22, 2019 11:02 pm

Great looking job.
Really brings the interior up to date.

dgmx5 · Post by **dgmx5** » Sat Aug 08, 2020 10:44 pm

Hi Alan

Are you still offering this service and how much?

ATB, David

dgmx5 · Post by **dgmx5** » Wed Oct 14, 2020 6:37 am

Bump. Are you still doing these Alan?

Number5 · Post by **Number5** » Wed Oct 14, 2020 6:15 pm

dgmx5 wrote: ↑Wed Oct 14, 2020 6:37 am Bump. Are you still doing these Alan?

Sorry, No. I've no stock left I'm afraid.

George7 · Post by **George7** » Wed Nov 25, 2020 3:22 pm

Hi Alan
Are you still doing this? Just found the article and wish I'd known about it earlier! I bought some piano black trims from another member and fitted myself, having had the rear consul out a couple of times before made it easier although the longest part is all of the damn torque screws in the centre consul. At least I could do those on the kitchen table!
The point to all of this is that I have a set of brushed aluminium, surplus to requirement, are you in the market to want any more or do you turn around enough from swaps. Let me know.
George

Number5 · Post by **Number5** » Thu Nov 26, 2020 9:07 pm

George7 wrote: ↑Wed Nov 25, 2020 3:22 pm Hi Alan
Are you still doing this?
George

Hi George,
No, not really. I havent done one for ages and only have one black set in stock, but have 3 bare Aluminium sets sat around.

As you will have discovered, its quite time consuming and fiddly, so I've just been concentrating on the roof motor relocations mainly for the past year or two, but thanks for the offer,

Alan

George7 · Post by **George7** » Thu Nov 26, 2020 11:04 pm

Alan
Thanks for the polite response, having relocated my roof motor some years ago, I'm interested how you deal with the cutting of the cable ties from the plastic retaining clip down in the well and have enough slack on the pipes to get it all back in the container???? Don't reveal your secrets to all, respond in a pm if you want

Regards
George

Number5 · Post by **Number5** » Fri Nov 27, 2020 8:32 pm

Hi George,
No problem. No Secret really, But unlike a few others who do it, I take the roof out so that I can clearly see what I'm cutting and am able to do more diagnostic/servicing work on the motor in a standing position, rather than crawling upside down in the boot.

Thunderous One · Post by **Thunderous One** » Fri Jan 01, 2021 5:26 pm

Is this service still available?

Z4-forum.com

Z4-forum.com