I have just been on holiday for 2 weeks only to come back to find my 2003 Z4 completely dead with a flat battery - I have charged it up and got the car going again but I think the windows no longer drop and the go back up that small amount to get a good seal with the roof........
Does anyone know how I can sort this out - I have seen some instructions for cars from 04/04 but what about those prior???
Help before it rains......
Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.
Window Problem
-
- Member
- Posts: 126
- Joined: Thu Jun 14, 2007 7:52 pm
- Location: Leicestershire
Window Problem
2003 Z4 2.5 - Grey with Red Leather
- IMZ4N
- Senior Member
- Posts: 1906
- Joined: Mon Jun 18, 2007 6:55 pm
- Location: Orange County CA
Stolen from another forum , orignally posted by inTgr8r
The Official Reset Proceedure
--------------------------------------------------------------------------------
Courtesy of a BMW tech on another forum, ...with thanks.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
• Initialization with engine running
• Convertible top, doors and windows closed
Initialization comprises:
• Erasure of initialization
• Reinitialization
An initialization must be performed:
• In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
• After the power window drive has been replaced
• After work is carried out on the power window mechanism
• After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
• After the door window glass has been removed and installed or replaced
• After adjustment work on the door window glass
• After adjustment work on the convertible top
• After replacement of seals
Erasure of initialization:
• Open door window glass fully
• Operate power window switch in "Open" position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
The Official Reset Proceedure
--------------------------------------------------------------------------------
Courtesy of a BMW tech on another forum, ...with thanks.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
• Initialization with engine running
• Convertible top, doors and windows closed
Initialization comprises:
• Erasure of initialization
• Reinitialization
An initialization must be performed:
• In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
• After the power window drive has been replaced
• After work is carried out on the power window mechanism
• After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
• After the door window glass has been removed and installed or replaced
• After adjustment work on the door window glass
• After adjustment work on the convertible top
• After replacement of seals
Erasure of initialization:
• Open door window glass fully
• Operate power window switch in "Open" position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
- sp3ctre
- Site Admin
- Posts: 7492
- Joined: Thu Jun 14, 2007 7:29 pm
- Contact:
-
- Member
- Posts: 126
- Joined: Thu Jun 14, 2007 7:52 pm
- Location: Leicestershire
- Ski
- Member
- Posts: 315
- Joined: Sun Jun 17, 2007 2:20 pm
- Location: Binghamton, NY
Nice find, thanks..IMZ4N wrote:Stolen from another forum , orignally posted by inTgr8r
The Official Reset Proceedure
--------------------------------------------------------------------------------
Courtesy of a BMW tech on another forum, ...with thanks.
Initialization is performed on the power window switch of the relevant door.
Requirements for correct initialization:
• Initialization with engine running
• Convertible top, doors and windows closed
Initialization comprises:
• Erasure of initialization
• Reinitialization
An initialization must be performed:
• In the event of malfunctions, e.g. no one-touch control function, no opening or if available no comfort function is possible
• After the power window drive has been replaced
• After work is carried out on the power window mechanism
• After a power supply interruption, e.g. disconnection of the battery or disconnection of the power supply to the door
• After the door window glass has been removed and installed or replaced
• After adjustment work on the door window glass
• After adjustment work on the convertible top
• After replacement of seals
Erasure of initialization:
• Open door window glass fully
• Operate power window switch in "Open" position four times within 10 seconds
This erases initialization of the power window, anti-trapping protection and toll function are inactive.
Check whether one-touch control (toll) function is inactive, otherwise repeat procedure.
Reinitialization:
Avoid a break between the two steps!
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
• Open door window glass fully
• Operate and hold power window switch in "Close" position (second switch stage)
• Once the upper end position has been reached, hold power window switch in "Close" position for approx. 2 seconds longer
My Jet Black's
'03 3.0i Z4 Loaded
'02 325Ci Loaded
'06 325xi Loaded