Bumper cutouts for twin exhausts..

Ducklakeview · Post by **Ducklakeview** » Sun Oct 08, 2017 11:13 am

Gonna be cutting my newly acquired facelift rear bumper for the extra outlets.

Anyone who's done it care to offer some hints and tips?

Mike

Silverzedtom · Post by **Silverzedtom** » Sun Oct 08, 2017 11:39 am

Can't offer any help I'm afraid but I'll be following with interest.

I was also concerned about the route over to the new tailpipe as our batteries are below the false floor rather than in the boot like the ///M

Ducklakeview · Post by **Ducklakeview** » Sun Oct 08, 2017 11:44 am

Silverzedtom wrote: ↑Sun Oct 08, 2017 11:39 am Can't offer any help I'm afraid but I'll be following with interest.

I was also concerned about the route over to the new tailpipe as our batteries are below the false floor rather than in the boot like the ///M

Nah, loads of room for a 50mm tube!

Mike

Silverzedtom · Post by **Silverzedtom** » Sun Oct 08, 2017 11:44 am

Zoomer · Post by **Zoomer** » Sun Oct 08, 2017 4:44 pm

What about templating the existing side and reversing the template. Are you putting a back box on the the side where you are adding the exhaust, or doing something else?

Ducklakeview · Post by **Ducklakeview** » Sun Oct 08, 2017 5:19 pm

Zoomer wrote: ↑Sun Oct 08, 2017 4:44 pm What about templating the existing side and reversing the template. Are you putting a back box on the the side where you are adding the exhaust, or doing something else?

No box, teeing off from my own modded oem box.

Mike

Post by **srhutch** » Sun Oct 08, 2017 7:48 pm

Hera you go, pawnsacrifices post from 2010

viewtopic.php?f=2&t=16689&hilit=Quad

Page 4

Zoomer · Post by **Zoomer** » Sun Oct 08, 2017 8:09 pm

In hope you will be taking lots of piccys Mike as it guess there will be a lot of interest in this

Ducklakeview · Post by **Ducklakeview** » Sun Oct 08, 2017 8:38 pm

srhutch wrote: ↑Sun Oct 08, 2017 7:48 pm Hera you go, pawnsacrifices post from 2010

viewtopic.php?f=2&t=16689&hilit=Quad

Page 4

Mike

85genius · Post by **85genius** » Sun Oct 08, 2017 9:03 pm

Something I've been considering on and off since I got my first zed...

My ultimate plan is to try and source some carbon fibre "eyebrows" to go above the twin exits at each side...

That's if I ever get to doing it

jarhead · Post by **jarhead** » Sun Oct 08, 2017 9:25 pm

MM did mine so worth sending him a PM.

JINGLE · Post by **JINGLE** » Tue Oct 10, 2017 7:40 pm

Not sure what route you will be taking, but you might need to move the charcoal filter over slightly (I removed mine completely)

Photo if it helps?!

JINGLE · Post by **JINGLE** » Tue Oct 10, 2017 7:43 pm

And this is the offending charcoal filter, ignore how dirty it all is, was last winter when I had to drive it on gritted roads

NOT THIS YEAR!!

Ducklakeview · Post by **Ducklakeview** » Tue Oct 10, 2017 8:08 pm

Shouldn't need to mess with the filter, I'm going to add an additional exit to my existing modded box, and tee across. It's a bit more involved with my box as the tee needs to come from one of the internal pipes I've fitted, rather than just the "box" otherwise the 2nd set of pipes won't have the same output.

Mike

Z4-forum.com

Z4-forum.com